裝載機http://m.lcsqtax.cn/鏟斗是裝載機用來收集、切削、鏟裝、運輸和卸載物料的工具，裝載機工作時的插入能力及鏟掘能力是通過鏟斗直接發揮出來的，鏟斗的結構形狀及尺寸直接影響裝載機的作業效率和可靠性。裝載機鏟斗形狀設計的合理，有利于減少插入阻力，提高鏟斗的鏟取力，使礦物流動順暢，大大提高鏟斗的工作效率。裝載機鏟斗工作的條件惡劣，需要較大的插入力，承受較大的沖擊載荷和嚴重的磨削，因此要求鏟斗應具有足夠的強度、剛度和耐磨性。
Loader bucket loader is used to collect, cutting tools, shovels, transport and unloading of materials, the ability to insert capability and shovel loaders at work is a direct play out through the bucket, the bucket structure shapes and sizes directly affect operational efficiency and reliability of the loader. Loader bucket shape design is reasonable, it helps to reduce the insertion resistance, improve scooping bucket of force, so that the mineral flowing smoothly,greatly improving the efficiency of the bucket. Loader bucket to work in bad conditions, requires a large insertion force, bear a greater impact load and severe grinding, thus requiring the bucket should have sufficient strength,stiffness and abrasion resistance.
  
裝載機鏟斗動臂和連桿的后端與車架支座鉸接，動臂和連桿的前端與鏟斗托架鉸接，托架上部鉸接轉斗油缸體，其活塞桿及托架下部與鏟斗鉸接。當托架、動臂、連桿及車架支座構成的是平行四連桿機構，則在動力提升、轉斗油缸閉鎖時，鏟斗始終保持平移，斗內東西不會抖落。裝載機鏟斗的下鉸接點即與動臂的連接鉸接點，當鏟斗在鏟掘位置時，應盡量使該點靠近切削刃與地面，下鉸接點靠近鏟斗切削刃，則轉斗時力臂小，有利于增加作用在斗刃上的掘起力。
Loader bucket boom and the rear end of the connecting rod bearing frame hinged boom and bucket linkage bracket hinged front, the upper hinge bracket bucket cylinder body, piston rod and the lower bracket and bucket hinge. When the brackets, boom, connecting rod and bearing frame is composed of a parallel four-bar linkage, in power lifting, bucket cylinder lock, the bucket remains translation, things will not shake off infighting. Under the loader bucket hinge point that is connected with the boom pivot point, when the bucket at the shovel position, you should try to make the point close to the cutting edge with the ground, the next pivot point near the cutting edge of the bucket, the bucket when arm small, will help to increase the role of the edge of the bucket breakout force.
   
裝載機http://m.lcsqtax.cn/鏟斗切削刃的形狀根據所鏟裝物料的不同而異，裝載機裝有斗齒的鏟斗，在裝載機作業時，插入力有斗齒分擔，形成較大的比壓，利于插入密實的料堆疏松物料，便于鏟斗的插入。裝載機用于插入阻力較小的松散物料或粘性物料，其鏟斗可以不裝斗齒。裝載機設計鏟斗的切削刀形狀、斗齒、側刀、斗體形狀、鏟斗容量等要根據鏟斗的設計要求和鏟斗斗型的結構分析來確定。
Loader bucket cutting edge shape depending on the loading shovel material varies, equipped with bucket loader bucket teeth, and when the loader operations, the insertion force there fighting tooth-sharing, leading to higher than the pressure, which will help to insert dense pile of loose material, to facilitate insertion of the bucket. Loader is used to insert a small resistance of loose materials or viscous material, which may not be loaded bucket bucket teeth.Loader bucket design cutter shape, bucket teeth, side cutter, bucket shape, bucket capacity, etc. should be determined based on structural analysis and design requirements of the bucket and bucket type.